悬链线竖向集中力作用下的构形分析和张力计算

目前,悬链线在竖向集中力和均布荷载共同作用下的构形分析和受力计算的理论仍不完善。针对这一问题,通过引入悬链线的几何约束方程、力平衡方程和超越方程,建立了竖向集中力与均布荷载共同作用下的非线性方程组。采用牛顿迭代法求解方程组,得到了悬链线的构形和受力情况。为了验证理论计算的正确性,进行了算例和试验验证。结果表明,算例的计算结果与文献结论保持一致,试验测得的构形和水平张力大小与理论计算的构形和水平张力大小吻合较好。本文的理论计算可以更加简单精确地计算出悬链线在竖向集中力和均布荷载共同作用下的构形和受力情况,为实际工程提供重要的理论指导。     

水硬性石灰合成及拉破坏特性试验研究

水硬性石灰在欧洲石质文物修复和加固中获得了很大成功。我国的石质文物主要是砂岩,水硬性石灰的修复效果不好。为满足我国石质文物修复和加固的需求,本文以石灰石和黏土为原料,在950℃煅烧不同时间,制备出水硬性石,对试样的成分、微观形貌、收缩率、抗拉强度和拉破坏过程等进行了研究。结果表明:(1)试样中含有水硬性成分2CaO·SiO2(C2S);煅烧8h时,成分与欧洲水硬性石灰NHL5接近;1.5CaO·SiO2·xH2O(C-S-H)和CaCO3的含量随龄期的增加逐渐增加。(2)龄期1~3d,收缩率较小;龄期4~6d,收缩率以线性规律增加;7d以后,收缩率趋于稳定。(3)局部变形区随拉应力的增加而变大,邻近局部变形区逐渐合并,形成面积更大的应变局部化带;载荷超过峰值后,产生微裂隙;随载荷进一步增加,微裂隙扩展,贯穿整个试件,发展成宏观裂隙,使试件破坏。(4)抗拉强度随龄期的增加而增加,水硬性石灰中C-S-H、CaCO3等相互交织,构成空间致密体,使试件力学强度提高。合成的水硬性石灰物理力学性能与欧洲水硬性石灰NHL5相近,并且成分均匀、可控,在石质文物修复和加固工程中具有良好应用前景。     

有耗介质层上多导体传输线的电磁耦合时域分析方法

目前,针对空间电磁场作用有耗介质层上传输线的电磁耦合,仍缺乏有效的数值分析方法.因此,本文提出一种高效的时域混合算法,很好地解决了有耗介质层上传输线电磁耦合建模难的问题.首先,对经典传输线方程进行改进,推导了适用于有耗介质层上多导体传输线电磁耦合分析的修正传输线方程.然后,结合时域有限差分方法和相应插值技术,求解修正传输线方程,获得多导线及其端接负载上的电压和电流响应,并实现空间电磁场辐射与多导线瞬态响应的同步计算.最后,通过相应计算实例的数值模拟,与CST软件的仿真结果进行对比,验证了时域混合算法的正确性和高效性.     

基于近似解析法的超导储能磁体设计

降低超导储能磁体的研制成本一直是控制超导磁储能系统(Superconducting Magnetic Energy Storage, SMES) 总成本的重要手段之一. 本文考虑在一定磁体结构参数范围内, 磁体产生的最大磁场值可以采用级数进行 表示, 磁体的电感值可以采用线性函数表示, 给出了超导储能磁体磁场能量的近似解析表达式, 提出了一种基于近 似解析法的超导储能磁体设计方法. 该方法以储能磁体的线材用量最小作为设计目标, 在给定超导线材参数和临界电流特性曲线, 以及磁体储能总量要求的情况下, 依据此方法可快速的得到成本最优时所对应的磁体结构参数.将近似解析法优化和采用传统的有限元软件 Ansys 仿真优化进行对比分析, 结果表明采用近似解析法进行磁体优化更加方便快捷, 节省了大量计算时间.     

高效液相色谱-荧光检测器法测定2-噁唑烷酮的含量

建立一种利用高效液相色谱结合荧光检测器准确测定2-噁唑烷酮含量的方法。样品中的2-噁唑烷酮和占吨氢醇在60℃的条件下衍生70 min后,直接进样分析。采用月旭XB-C18色谱柱,流动相为0.02 mol/L乙酸钠水溶液和乙腈,检测器波长为λex=213 nm,λem=308 nm,流速1.0 mL/min,柱温35℃的条件下。2-噁唑烷酮浓度在0.5~50.0mg/mL时,线性关系良好(R2=0.9995),检测限和定量限分别为0.005 mg/L、0.016 mg/L。该方法准确、灵敏、快速,适用于2-噁唑烷酮含量的检测。     

System-size effect on the friction at liquid-solid interfaces

The friction at the liquid-solid interfaces is widely involved in various phenomena ranging from nanometer to micrometer scales. By the molecular dynamic(MD)simulation, the friction properties of liquid-solid interfaces at the molecular level are calculated via the Green-Kubo relation. It is found that the system size will influence the value of the friction coefficient, especially for the solid surfaces with the larger polar charge. The value of the friction coefficient decreases with the increase in the system size and converges at large system sizes. The large polar charge will lead to a significant friction coefficient. However, the diffusion of water molecules on this surface is almost a constant, indicating that the diffusion coefficient seems to be independent of the system size and polar charge. This work provides insights for the selection of the system size in modeling the frictional properties of hydrophobic/hydrophilic surfaces.     

Synthesis of poly(n‐butyl acrylate) homopolymer and poly(styrene‐b‐n‐butyl acrylate‐b‐styrene) triblock copolymer via AGET emulsion ATRP using a cationic surfactant

Cationic emulsions of triblock copolymer particles comprising a poly(n‐butyl acrylate) (PⁿBA) central block and polystyrene (PS) outer blocks were synthesized by activator generated by electron transfer (AGET) atom transfer radical polymerization (ATRP). Difunctional ATRP initiator, ethylene bis(2‐bromoisobutyrate) (EBBiB), was used as initiator to synthesize the ABA type poly(styrene‐b‐n‐butyl acrylate‐b‐styrene) (PS‐PⁿBA‐PS) triblock copolymer. The effects of ligand and cationic surfactant on polymerizations were also discussed. Gel permeation chromatography (GPC) was used to characterize the molecular weight (M_n) and molecular weight distribution (MWD) of the resultant triblock copolymers. Particle size and particle size distribution of resulted latexes were characterized by dynamic light scattering (DLS). The resultant latexes showed good colloidal stability with average particle size around 100–300 nm in diameter. Glass transition temperature (T_g) of copolymers was studied by differential scanning calorimetry (DSC). © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 611–620     

Synthesis and Herbicidal Activities of 3‐(4‐Chloro‐2‐fluoro‐5‐substituted phenyl)benzo[d][1,2,3]triazin‐4(3H)‐one Derivatives

A series of 3‐phenyl benzo[d][1,2,3]triazin‐4(3H)‐one derivatives were synthesized through the condensation of phenol E and alkyl (alkenyl, alkynyl) chlorides (bromides, iodide) or alkyl chloroacetates or N‐alkyl chloroacetamides using K₂CO₃ as the acid acceptor in N,N‐dimethylformamide. Phenol E was prepared from starting material, 5‐amino‐2‐chloro‐4‐fluorophenyl ethyl carbonate, in four steps involving in amidation, reduction, diazotization, and deprotecting‐group reaction. The herbicidal activities of the title compounds were tested against two dicotyledonous plants and two monocotyledonous plants, in which some of them exhibited high herbicidal activities against two dicotyledonous plants in preemergence and postemergence treatments. Moreover, when the dosage was decreased to 180 and 90 g/ha, compounds F1 , F8 , and F9 showed highly selective inhibitory activities against amaranth pigweed, alfalfa, asteraceae, field sowthistle, morning glory, purslane, and velvetleaf in postemergence treatment but had no herbicidal efficacy on rape except F1 , suggesting that it be possible to find a kind of herbicides to inhibit dicotyledonous weeds in the field of dicotyledonous crops with the same genus as aforementioned weeds.